Material Handling Equipment

Bucket elevators are designed to move flowing powders or bulk solids vertically. Bucket elevators use an endless belt or chain and have a series of buckets attached to it. Bulk material is spread into an inlet hopper. Buckets (or cups) dig into the material and convey it up and over the head sprocket/pulley, and then throw the material out a discharge throat.

Bucket elevators are not self-feeding and are fed at a controlled rate. The buckets are usually where the chain or belt path is vertical or steeply inclined in a single plane. The buckets are returned back down to a tail pulley or sprocket at the bottom.

There are four broad classifications of bucket elevators: centrifugal, continuous, positive, and internal discharge. The most commonly used are the centrifugal and continuous discharge elevators.

Ultra Febtech Pvt. Ltd. industrial bucket elevators are made in a variety of shapes, weights and sizes, Z type bucket elevator, C type bucket elevator all utilizing centrifugal buckets or continuous buckets.

Bucket Elevator:
Continuous bucket elevators are used to handle friable, fragile materials because they minimize product damage or are used to handle light fluffy materials where aeration of the product must be avoided. Continuous bucket elevators have buckets spaced continuously and operate at slower speeds. The continuous bucket placement allows the force of gravity to discharge their load onto the inverted front of the proceeding bucket. The bucket then guides that material into the discharge throat on the descending side of the elevator.

Because every bucket application is unique, Ultra Febtech Pvt. Ltd. offers a broad series of industrial elevator designs like Z type bucket elevator, C type bucket elevator etc. Selection of the proper type of bucket elevator depends largely on the capacity requirements and the characteristics of the material to be handled; which are dependent upon customer's requirement too.

Advantages:

• Stainless steel and MS painted construction
• Easy installation
• Heavy gauge angle iron
• Bearing jack bolts for shaft alignment
• Long, contoured head
• Heavy-duty motor mount
• Hinged lagging inspection door with quick latch
• Adjustable wiper belt
• Engineered head shafts
• Angle reinforcement kicker
• Oversized discharge
• Lip seal for protection from elements
• Replaceable head and hood lining

Rotary Table Feeders are used in industries, which require the moving or feeding of powder or granular substances. Table feeders are particularly helpful in moving sticky or hard to feed materials. They are also very useful in converting an intermittent batch process into a continuous material feeding process.

The amount of material leaving the rotary feeder can be controlled by changing the angle of the discharge plow via a hand wheel or by the motor.

We Ultra Febtech Pvt. Ltd. - An ISO 9001:2008 certified company make bucket elevator system as a part of material handling equipment A bucket elevator, is a mechanism for handling flowable bulk materials vertically.

It consists of:

• Buckets to contain the material
• A belt to carry the buckets and transmit the pull;
• Means to drive the belt
• Accessories for loading the buckets or picking up the material, for receiving the discharged material, for maintaining the belt tension and for enclosing and protecting the elevator.
• A bucket elevator can elevate a variety of bulk materials from light to heavy and from fine to large lumps.
• A centrifugal discharge elevator may be vertical or inclined. Vertical elevators depend entirely on the action of centrifugal force to get the material into the discharge chute and must be run at speeds relatively high. Inclined elevators with buckets spaced apart or set close together may have the discharge chute set partly under the head pulley. Since they don''t depend entirely on the centrifugal force to put the material into the chute, the speed may be relatively lower.

Belt Driven Blower is mainly used for transmission of air outside from various locations. It has got a wide range of applications like industrial, environmental, instrumentation, and chemical processing applications. Our centrifugal blower is designed after a long research work carried out for specific requirements of our customers. We have developed the blower with special features more airflow in lower power consumption, maintenance free, long life smooth running with direct drive or V-belt driven. We make a wide range of standard and customized blowers in MS and SS materials & various models.

Pneumatic Flash Dryer will be effectively used for drying the wet material and convey it. The drying takes place in a wide and high vertical tube. The material is sucked into the tube with a negative suction. The hot air is also carried with the material. Cyclones will be attached for the air and material separation. The necessary airlock will be provided with the system.

We are providing Industrial Boiler to our clients as per their requirements.

0.5HP Rotary Air Lock Valve is suited for low and medium differential air pressure systems, gravity, or volumetric feeder discharge equipments. This will allow free flowing solids to pass from one to another valves space with a different air pressure. Rotary airlock is useful as one component in a bulk or specialty material handling system.